784748 D01 General labeling and Notification v09
Page 1
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
April 9, 2018
GENERAL GUIDELINES FOR LABELING AND OTHER INFORMATION REQUIRED TO BE PROVIDED TO USERS
1. INTRODUCTION
General equipment labeling requirements are found in Part 2 Subpart J. Additional requirements for
device labeling, information to users or information required to be displayed for specific to RF devices is
specified in the applicable rule part for the RF device (e.g., Sections 15.19, 15.105).1
The labeling and
compliance information required for a given product is based on the equipment authorization procedure
prescribed in the specific FCC rules that apply to the product
The Commission has two equipment authorization procedures: (1) Supplier’s Declaration of Conformity
(SDoC),
2
and (2) certification. 3
The label requirements for an RF device will depend on the type of
equipment authorization used. Many of today’s products are composite devices that include both radio
transmitter(s) and digital circuitry. For these devices SDoC may be used for the digital circuitry portion
of the device and certification for the transmitter portion. However, certification may be used to
demonstrate compliance for both the transmitter and digital circuitry portions.
Appendix A provides a non-exhaustive list of compliance information requirements and information-toend
user.
2. SUPPLIER’S DECLARATION OF CONFORMITY (SDoC)
2.1 Product Identification
The product identification (labeling) and compliance information requirements for a device subject to
SDoC (Sections 2.1074 and 2.1077, respectively) requires that each device be uniquely identified (for
example, using a label listing a trade name and type or model number),
4
and that end-users must be
1 See 47 CFR §§ 15.19 and 15.105.
2 See 47 CFR §§ 2.906 et seq.
3 See 47 CFR §§ 2.907 et seq.
4 FCC 96-208, docket no. 95-19, 11 FCC Rcd 17928, “28. Decision. As proposed, we are replacing the existing FCC
ID label on personal computing equipment with a new, simplified label that includes a compliance logo. ...
Consistent with our existing rules, we are also requiring that the new labels for computing devices uniquely identify
the product with a trade name and type or model number. ...”
784748 D01 General labeling and Notification v09
Page 2
provided with a compliance information statement for the product.
5
The unique identifier is any means to positively associate the device with the compliance test reports and
records for a specific product approved using the SDoC procedure.6
This may be a trade name and type
number, model number, serial number, or other means employed utilizing the responsible party’s internal
manufacturing process.
2.2 Compliance Information
A compliance information statement that includes the following items (Section 2.1077(a)) must be
supplied with the product at the time of marketing or importation:7
Identification of the product, e.g., trade name, model, etc.
A statement that the product complies with the rules, as applicable;8
; and
The name and address, and telephone number, or internet contact information of the responsible
party’s (as defined in Section 2.909(b)) contact located in the United States.
9
2.3 Compliance Information for Assembled Products
Further to Section 2.1077(b), the following items apply to products: (1) assembled from modular
components (e.g., enclosures, power supplies and CPU boards) that, by themselves, are authorized under
SDoC and/or a grant of certification; and (2) where the assembled product is also subject to authorization
under SDoC but, in accordance with the applicable regulations, does not require additional testing. This
is applicable to personal computers under Section 15.101 (KDB 657217 Personal Computers). Such
products shall be supplied, at the time of importation or marketing, with a compliance information
statement containing the following information:
Identification of the assembled product, e.g., name and model number.
Identification of the authorized modular components used in the assembly. Authorized modular
components shall be identified as specified in Section 2.1077(a)(1) for SDoC procedures or
Section 2.925 for certification.10
A statement that the product complies with appropriate rules.
5 See 47 CFR §§ 2.1074 and 2.1077. Also, See KDB Publication 896810 for guidance on Supplier’s Declaration of
Conformity.
6 See 47 CFR § 2.938 for further requirements for test reports.
7 An example of a Supplier’s Declaration of Conformity document template is given in Appendix A of KDB
Publication 896810 D01.
8 For devices subject to Part 15 and 18 rules, the statements require in Sections 15.19(a)(3) and 18.212, respectively
meets the requirements of this rule part.
9 FCC 17-93, docket no. 15-170, para 16. “Given the widespread and effective use of direct internet contact for
dialogue between consumers and businesses, we therefore will allow responsible parties the option of providing an
internet-based means of contact in lieu of a telephone contact number. …”
10 See 47 CFR §§ 2.1077 and 2.935. Devices subject to certification require an FCC Identifier.
784748 D01 General labeling and Notification v09
Page 3
The identification, by name and address and telephone number or internet contact information of
the responsible party who assembled the product from authorized modular components.11
For
devices authorized under SDoC, the responsible party must be located within the United States.
Copies of the compliance information statements for each modular component used in the system
that is authorized under SDoC.
2.4 Placement of Compliance Information
Further to Section 2.1077(c), the compliance information must be provided in a form that an end-user can
reasonably be expected to have the capability to access, such as the instruction manual, a separate product
insert, computer disk, web page, or the device’s own electronic screen. Compliance information may be
provided electronically as permitted in Section 2.935.
2.5 FCC Logo
Devices authorized under the SDoC procedure have the option to use the FCC logo to indicate
compliance with the FCC rules,
12 and the logo may be included in the instruction materials or as part of
an e-label.
The FCC logo shall only be used on a product that has been tested, evaluated, and found to be compliant
in accordance with the SDoC procedures. The use of the FCC logo on the device does not mitigate the
requirement to provide a means to uniquely identify the product or to provide the required compliance
information statement. The FCC logo cannot be used on products that are exempt from an authorization
by rule (e.g., Section 15.103 exempt devices, or Section 15.3 incidental radiators) unless the SDoC
procedure has been fully applied for the product.
3. CERTIFICATION
For certification, the product shall bear a nameplate or label with the FCC Identifier (FCC ID), as defined
in Section 2.925.13
The FCC ID must always be accessible when using the product. The placement of the
FCC ID must be a physical label on the product, unless an e-label is used.
Physical FCC ID labels must be located on the surface of the product, or within a user-accessible nondetachable
compartment (such as the battery compartment). The label shall be permanently affixed,
permitting the device to be positively identified. The font needs to be readily legible, consistent with the
11 Responsible parties as defined in Section 2.909 (47 CFR § 2.909).
12 See 47 CFR § 2.1074(b). FCC logos using other formats, such as those found https://www.fcc.gov/general/logosfcc,
are not appropriate for compliance purposes.
13 See 47 CFR §§ 2.925 and 2.926.
784748 D01 General labeling and Notification v09
Page 4
dimensions of the equipment and its label area.
When the device is so small, or for such use that it is impracticable to label with a font size that is fourpoints
or larger (and the device does not utilize electronic labeling), then the FCC ID shall be placed in
the user manual, and the FCC ID shall also be placed either on the device packaging or on a removable
label attached to the device.
4. ELECTRONIC LABELING
Products with a built-in display, or that only operate in conjunction with another product that has an
electronic display, have the option to display on the electronic display the FCC Identifier, any warning
statements, or other information that the Commission’s rules would otherwise require to be shown on a
physical label attached to the device.14
Guidance for electronic labeling is provided in a separate
attachment–see KDB Publication 784748 D02.
5. PACKAGING INFORMATION
Some RF devices are also required to have information included in the packaging of the device (see
Appendix A of this document):
E-Label. Devices displaying their FCC ID, warning statements, or other information electronically must
also be labeled, either on the device or its packaging, with the FCC ID and other information (such as a
model number) that permits the devices to be identified at the time of importation, marketing, and sales as
complying with the FCC’s equipment authorization requirements.15 This requirement is in addition to the
electronic labeling of the device. Devices can be labeled with a stick-on label, printing on the packaging,
a label on a protective bag, or by similar means. Any removable label shall be of a type intended to
survive normal shipping and handling, and must only be removed by the customer after purchase.16
Signal boosters. The advisories shall be provided in on-line, point of sale marketing materials, in print or
on-line owner’s manual and installation instructions, on the outside packaging of the device, and on a
label affixed to the device.17
Change Notice
07/11/2014: 784748 D01 Labeling Part 15 &18 Guidelines v08 replaces 784748 D01 Labeling Part 15
&18 Guidelines v07. Changes were made to reference new guidelines for electronic labeling in the new
attachment 7784748 D02 e labeling v01 for e-label guidance,
04/09/2018: 784748 D01 General labeling and notification v09 replaces 784748 D01 Labeling Part 15
&18 Guidelines v08. Changes have been made to reflect changes in the rules in accordance with FCC
17-93. Labeling guidance for multi-enclosure transmission-system equipment is added in Appendix A.
14 See 47 CFR § 2.935.
15 See 47 CFR § 2.935(f).
16 See 47 CFR § 2.935(f).
17 See 47 CFR § 20.21(f)(1).
784748 D01 General labeling and Notification v09
Page 5
APPENDIX A
COMPLIANCE INFORMATION AND INFORMATION TO USER
REQUIREMENTS SUMMARIES
A.1 INTRODUCTION
This appendix provides additional guidance on the specific labeling and compliance information for
various common products subject to the FCC equipment authorization procedures (SDoC or certification
or both). This list in this appendix is not exhaustive of all the compliance information, information to
user or display requirements; it provides information about commonly applicable rule parts.
A.2 PART 15 COMPLIANCE INFORMATION
Products authorized under Part 15 using SDoC require a label containing one of the following compliance
statements (as specified in Section 15.19(a)):
Receivers associated with licensed radio service operations:
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this
device does not cause harmful interference.
Stand-alone cable input selector switch:
This device complies with part 15 of the FCC Rules for use with cable television service
All other devices:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
This device labeling requirement is in addition to the SDoC compliance information statement and label
requirements of Sections 2.1074 and 2.1077; however, placing the Part 15 compliance information will
also satisfy the requirements for Sections 2.1074 and 2.1077. When the device is so small, or for such use
that it is impracticable to label it with the compliance statement specified in a font that is four-point or
larger, and the device does not have a display that can show electronic labeling,18 then the information
required shall be placed in the instruction manual, and on the device packaging or on a removable label
attached to the device. In cases where the instruction manual with the compliance information is a printed
document provided along with the device, the arrangement is acceptable for compliance with the Part 2
and 15 rules for information to the user. Where the instruction manual is not a printed document, a paper
slip printed with the Part 15 compliance information and included with the device will also meet the
requirement of the rules.
A.3 PART 15 INFORMATION TO THE USER
1. For devices approved under Part 15, the user’s manual or instruction manual for an intentional or
unintentional radiator shall caution the user about changes or modifications to the device (Section
15.21).
18 See 47 CFR § 2.935.
784748 D01 General labeling and Notification v09
Page 6
2. For Class A and Class B digital devices, information to the user is required to include the
following statements (Section 15.105):
For a Class A digital device or peripheral, the instructions furnished to the user shall include
the following or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
For a Class B digital device or peripheral, the instructions furnished to the user shall include
the following or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
A.4 PART 18 COMPLIANCE INFORMATION
Products authorized under SDoC and Part 18 required to include a compliance statement similar to the
following: 19
“This device complies with Part 18 of the FCC Rules.”
The compliance information may be placed in the instruction manual, on a separate sheet, on the
packaging, or electronically as permitted in Section 2.935. There is no specific format for this
information. The placing of this or similar statement will also comply with the requirements of Section
2.1077(a) (2).
19 See 47 CFR § 18.212.
784748 D01 General labeling and Notification v09
Page 7
A.5 PART 18 INFORMATION TO THE USER
For devices approved under Part 18, information on the following shall be provided to the user in the
instruction manual, or on the packaging if an instruction manual is not provided (Section 18.213):
The interference potential of the device or system.
Maintenance of the system.
Simple measures that can be taken by the user to correct interference.
For RF lighting devices, provide an advisory statement, either on the product packaging or with other
user documentation, similar to the following:
This product may cause interference to radio equipment and should not be installed near
maritime safety communications equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.
Variations of this language are permitted provided all the points of the statement are addressed, and
may be presented in any legible font or text style.
A.6 CERTIFIED TRANSMITTER MODULES
All standalone modules without an integrated display on the module must be labeled with the module’s
FCC ID. Only modules with a display can use e-labeling (see also KDB Publication 784748 D02). A
host product20 shall use a physical label stating “Contains Transmitter Module FCC ID: XYZMODEL1,”
or “Contains FCC IDs: XYZMODEL1, XYZMODEL2,” or shall use e-labeling.21
A.7 CERTIFIED SOFTWARE DEFINED RADIO
A software defined radio approved under Section 2.944 may use either permanently affixed labels, or use
e-labeling, if the host device has an electronic display.
22
A.8 RF EXPOSURE INFORMATION
In many instances it may be necessary to provide additional information to the user for RF exposure
compliance., Such RF exposure user information must be provided either with instructions manual on
how the device accessories must be used for RF exposure compliance, or at minimum, instructions on
how to reasonably obtain these instructions. RF exposure labeling and notification requirements are
specified in Sections 2.1091 and 2.1093.23 Further guidance for equipment used in generalpopulation/uncontrolled
or occupational/controlled environments is provided in various KDB
Publications.
24 RF exposure compliance user information may be displayed using the e-labels.
20 Any product, system, or equipment that uses a certified transmitter module is referred to as the host.
21 See 47 CFR § 15.212 and KDB Publication 996369 for other details.
22 See 47 CFR § 2.944
23 See 47 CFR §§ 2.1091(d) and 2.1093(d).
24 See KDB Publications 447498, 616217, 648474 and 941225.
784748 D01 General labeling and Notification v09
Page 8
A.9 SIGNAL BOOSTERS
Guidance on labeling for consumer and industrial signal boosters, and warning label for consumer signal
boosters operating under Sections 20.21 and 90.219 is provided in KDB Publication.
25 The user
information and notification requirements are also discussed in the KDB Publication.
A.10 SECTION 20.19 HEARING AID COMPATIBILITY (HAC)
Handsets must clearly display the HAC rating on the packaging material; it is not sufficient to include the
information only in an e-label. See the section on user’s manual and disclosures in KDB Publication.26
A.11 MULTIPLE-ENCLOSURE AND TRANSMISSION SYSTEM EQUIPMENT
Where a transmission system has a component-device serving as the “main control unit,” e.g., the signal
source or exciter, conventional FCC ID rules and policies shall be used for affixing the label to that
component. For some system configurations, labeling the FCC ID on the system component-device
having the main RF output port may apply.
Other component-device enclosures (e.g., a rack) shall not use the same FCC ID label; such enclosures
typically are not complete transmitters or transmission systems, nor are they transmitter-control devices.
Examples include scenarios where a system contains multiples of the same power amplifiers that are used
with broadcast transmitters27; or where a multi-carrier power amplifier (MCPA) is used with a
cellular/PCS base-station main unit.
Conventional “full-transmitter” FCC ID labeling should not be used on secondary component-devices
that are marketed and operated only as part of a specific system.
While not required, system-secondary component enclosures may optionally be labeled by including text
“Part of System FCC ID xxxxxx,” or similar, where “FCC ID xxxxxx” is the FCC ID labeled on the
system primary-device enclosure.
25 See 47 CFR §§ 20.21 and 90.219. Also, KDB Publication 935210 D02 v04 section III0 b) and d).
26 See 47 CFR § 20.19 and KDB Publication 285076.
27 KDB Publication 754507.